NEW PATENT PENDING TRUE CO-WITNESS - MFI Micro Red Dot Scope Mount for Aimpoint T2 Footprint Universally Fitting All Variants & All Calibers of MP5 / HK94 / HK G3 / HK91 / HK93 including .22 LR / Price includes USPS Priority Mail & Insurance

THIS ITEM COMES WITH FOOTPRINT FOR AIMPOINT T2.

Unlike my other Micro Red Dot Scope Mounts, the Aimpoint T2 mount is a dedicated footprint and thus does not have a removable footprint plate. The reason why I did not do a plate for the T2 is that it was not possible, as I have to push the T2 Optic farther forward in order for the pop up scope lens covers to clear the rear sight on the HK91 and HK93 models. Depending on the model the rear cover does slightly hit the rear sight, but still opens and closes in the right position.

This is the NEXT GENERATION of MFI scope mounts for HK G3 / MP5 weapons platforms. MFI optic mounts for the HK MP5 and HK G3 series have been used the world over for the past 2 decades. Over those many years little has changed in our mounting platform, but recently I have come up with improvements that greatly enhance the platforms universality and flexibility.

Many of you have asked for a 100% True Co-Witness with the iron sights using a red dot sight, this is now possible!

If you look at the 2nd to the last photo you will see a shot looking down sight plane of an Aimpoint T2 mounted directly to an MFI Micro Red Dot T2 scope mount on a customer's HK MP5K PDW. It is really hard to get photos like this that are in focus and undestroyed, so that I can demonstrate the co-witness.

Remember that this is a Aimpoint T2, which has one of the taller profiles in the Micro Red Dot Optic category, so clearly any optic sight lower will also allow a True 100% Co-Witness with the HK G3 / HK MP5 drum / diopter sights.

NEW PATENT PENDING - MFI Micro Red Dot Scope Mount with Aimpoint T2 footprint WILL universally fit all variants for all manufacturers worldwide & for all calibers of MP5 / HK94 / HK G3 / HK91 / HK93 including but not limited to:

• HK MP5 all models
• HK SP5 / SP5-L all models
• HK94 / AP5 / AP5-L all models
• MAC-5 Military Armament Corporation MAC5 all models
• MKE AP5 / Zenith ZF-5 all models
• Special Weapons SW5 / Coharie
• PTR-9 (without the welded rail) all models
• Dakota Tactical D54 (without the welded rail) all models
• Norinco NR08 / Chinese MP5 Clone all models
• HK91 / AP91 / PTR91 all models
• HK G3 / Century Arms C308 all models
• Springfield Armory SAR-8
• HK93 / AP93 / V93 / PTR-93
• Century Arms AP53 MKE AP-53 / Zenith 33K / MKE Z43P / Vector V53 all models
• GSG MP5 .22 all models
• Umarex MP5 .22 all models

All foreign made models of the above regardless of country of origin.

NOT for Portuguese FMP / CA-3 / CETME L OR C unless they have the recoil stop block in front of the rear sight. See the very last photo to fully understand and identify if your weapon has a recoil stop block or not as it is required for this product.

---

Specifications:

• 100% Made In the USA.
• True 100% Co-Witness with iron sights through the Micro Red Dot Sight.
• Mounts WITHOUT removing the screws from the legs.
• 6061 T-6 Aircraft Grade Aluminum (Main Body of the Mount)
• CNC Machined from billet.
• Weapons Grade Hardened Steel Legs / Hooks. Mil. Spec. Black Oxide Coating.
• Patented Design (Utility): Pending 03-27-2025
• Anti-Recoil Lug / Will not slide off your receiver.
• Hard Anodized Flat Black
• Ultra-Light Weight @ 73.70 gr. ( 2.6 oz. )
• 3.370 Inches ( 87.77mm ) Long.
• Ultra-Low Profile Height @ 0.1890" ( 4.80mm ).
• 100% Mil. Spec. T2 Footprint.
• Tolerance held is + / - 0.001 (less than the thickness of a piece of paper).
• 4 – Independently Adjustable Claws / Legs for secure mounting to the weapon.
• 4 – Independently Adjustable Set Screws for Windage / Mount Centering.
• Professionally Laser Engraved.

The mount does NOT Interfere with the iron sights when a red dot is not in place. There is a 100% clear unobstructed view over the top of the rail.

This new design (goes for all new MFI Micro Mounts) fits all known HK G3 and MP5 variations genuine HK or clone as plug and play, including the weird out of spec clones and .22 LRs.

---

COMES WITH:

• 1 – Main Body / Mount with Built-In Dedicated Aimpoint T2 / H2 Footprint.
• 4 – Steel Claws / Hooks
• 4 – Steel US 4-40 X 5/16” bolts for claws. Max. Torque @ 2-3 inch pounds
• 4 – Steel US 6-32 X ¼” set screws for windage adjustment / centering.
• 1 – 1/16” Allen wrench for set screws and plate screws
• 1 – 3/32” Allen wrench for claws / hook bolts
• Limited Life-Time Warranty / My lifetime, so once I am dead it is likely over.

---

IN DEPTH DESCRIPTION / KEY FEATURES / IMPROVEMENTS:

A TRUE 100% CO-WITNESS WITH IRON SIGHTS:

True 100% Co-Witness with iron sights through Aimpoint T2 Micro Red Dot Sight & Most Micro Red Dot Sights with the same footprint.

WEAPON'S MOUNT DOES NOT BLOCK THE IRON SIGHTS &
100% UNOBSTRUCTED VIEW WITHOUT A OPTIC IN PLACE:

The mount does NOT Interfere with the iron sights when a red dot is not in place. There is a 100% clear unobstructed view over the top of the rail, without blocking any of the front or rear sights.

A TRUE UNIVERSAL FIT:

More Universally fitting instead of special mounts for different calibers and manufacturers whose receivers are out of spec. This mount solves all that and UNIVERSALLY FITS ALL MODELS of HK MP5 and G3 regardless of when or where manufactured or even caliber including the .22 LRs.

After more than 2 decades with 100,000+ mounts sold, years of RND / examining customers poor welds on per-1998 MP5s and testing on 100s of different models of G3 & MP5, I have come up with what I believe is the ultimate profile for the underside of all our new scope mounts, which allows our mounts to UNIVERSALLY FIT all the variations out there, no matter how out of spec they may be.

100% SECURE ATTACHMENT:

4 - Independent Draw Style Hooks for 100% Secure Attachment. This solves any deviation is sheet metal stamping and bending.

Having 4 independently controlled contact points (via the claws / hooks) that grab the optics mounting points via the sheet metal gussets is critical as the gussets on the right side generally have a shelf cut in them, whereas the gussets on the left side do not. Additionally, the nature of stamped sheet metal, especially in older foreign clones, unbent flats and home builds, the gussets front to back may not be a uniform identical shape.

EASE OF MOUNTING:

You do NOT need to completely remove the screw / bolt to attach the scope mount.

Nor, should you remove the bolt from the claw / hook when mounting!

The Claw / Hook can have the bolt / screw attached and the mount as a single unit, with the 4 claws / hooks can be slipped onto the weapon, aligned and secured without completely removing the screw / bolt from the claw / hook. No other scope mount for the HK MP5 / G3 series can do this.

Part of the above “Universality” is a new Claw / Hook design that allows the mount to go on without completely removing the bolt from the claw / hook. This also basically eliminates the possibility of cross threading the claw / hook.

Just loosen the screw as far as you can WITHOUT having the claw / hook disengage from the screw. If you look closely, you will see the top of the claw clear the bottom of the mount's cut out, allowing the claw to splay outward, thus clearing the sides of the receiver.

To tighten the screws, you will gently push the bottom of the claw up forcing the screw to rise, so you can use the supplied Allen Key to just take up the slack on all screws. Once you just have the slack taken up you can look at the front of the mount where the gap is between the mount and the receiver. You want to have equal space on either side to ensure that the mount is centered. If needed you can use the 4 independently adjustable set screws on each leg of the mount to hold center (More on this below). Then continue to draw the claws up in a rotational fashion. Do NOT tighten one screw and move on. As you tighten the screws you can look at the sides of the mount and assure that it is sitting flat and level. Holding the Allen key with your fingers on the SHORT end and the LONG end engaged in to the screw head (this keeps you from using any significant leverage, you will gently draw up all 4 screws. Once all 4 screws are to the point where they do not move easily… STOP!

Maximum torque is 2-3 INCH pounds not foot pounds!

At this point you can move the Allen key around and engage the short end into the screw head and turn a maximum of 3/4 of one rotation.

Torque Drivers / Torque Wrenches that read under 10 INCH pounds are usually over $100.00 and 95% of you will NOT have one. So, once the screw stops turning while you are holding the SHORT end, you should stop.

Never use thread locking compound on the set screws or the screws that hole the claws / hooks as these are held in place by constant reverse pressure from the opposite side screws and undoing them would be very difficult and likely end up damaging the thread on the claw or cause the head on the bolt to strip.

So, no more trying to thread a blind hole from the opposite side while holding a weapon upside-down like other mounts require you to do.

The above basically eliminates the possibility of cross threading the bolt or claw, as the screw never leaves the claw.

The 4 side set screws (if needed) can be used to fine adjust the centering of the mount on the receiver

Some MFI mounts also have a set screw located between the front legs on the mount (on 1913 Picatinny Rail mounts the screw is in the slot. 99% of the time this set screw is NEVER used. This is only there for receivers that are really out of spec. on the top and require a slight amount of rise to make the level with the barrel / receiver / plane of the bullet path.

---

TORQUE WARNING: The bolts for the Claws / Hooks are #4-40 and the maximum torque is very slight @ 2-3 INCH pounds NOT FOOT pounds. Basically imagine if you had a small pre-drilled 1/2" deep hole in a piece of pine (very soft wood) and you used the appropriate size wood screw (say a #8 sheet rock screw) to just turn the screw into the hole to the bottom of the hole, that twisting action is likely 2-3 inch pounds, once the tip of that wood screw hits the bottom of the hole you have maybe a 3/4 of a full turn before you exceed 4 inch pounds. I have to use very small bolts to allow the heads of those bolts to NOT interfere with placing anything i.e. a scope ring or clamp along the mounting surface. Larger bolts just get in the way.

---

Watch this video for installation instructions:

https://www.youtube.com/watch?v=XRrB95oMnx4&t=1s

Yes, that is me and I am a one man show, so all my videos will be unsophisticated as I do not have the time of funds to make slick, entertaining clips.

---

WINDAGE ADJUSTMENT / BETTER CONTACT FOR OUT OF SPEC. RECEIVERS:

A very unique feature of my new MFI mounts is the addition of 4 set screws / one per leg on the skeleton mount allow for windage adjustment / an adjustable centering / perfect alignment of the mount with the center line of the weapon. The 4 Set screws allow an adjustable tight fit regardless of out of spec. receiver. Meaning the set screws can take up any slack or looseness in the mount's body to allow a perfect fit to the receiver regardless of out of spec the receiver may be.

No other scope mount currently on the market has this ability. I am a fan of all things firearms, especially history and have only seen scope mounts and or scope rings from the 1920s and 1930s that have this ability and only because 95% of all scopes of the period lacked any windage adjustment and those that did were extremely limited.

---

---

I do offer other footprints, here is a list of the ones I currently make.

• Aimpoint ACRO = MFI Micro Rail.
• DOCTOR / Noblex / Tru*Tec Micro / Vortex Viper = MFI Plate #1
• Trijicon RMR = MFI Plate #2
• Trijicon RMS / Shield / Leupold Delta Point / EoTech E-FLX = MFI Plate #3 ( Included with this item. )

---

If you have a Red Dot Sight that utilizes a Mil. Spec. 1913 Picatinny Rail, then you must buy the MFI HK MP5/G3/93 Micro Low Mount, which I make EXCLUSIVELY for HKPARTS.NET and here is the direct link for that mount:

https://hkparts.net/h-k-rifle-smg-parts/mfi-hk-mp5-g3-93-micro-low-mount/

---

All MFI products are made Specifically for LIVE WEAPONS. In other words this is NOT some toy or piece of airsoft CRAP made of questionable pot metal in foreign factories by people who have never even seen a real machine gun. Others less reputable dealers are known to try to sell items that were intended for airsoft bb guns and hope you do not notice until it is too late... meaning when you are dead due to a failure of their untested / junk product.

MFI is the GENUINE ARTICLE / REAL DEAL that others copy. Designed for Specifically for all HK G3 & MP5 weapons platforms worldwide.

Note that the attachment mechanism is NOT a quick release style like found on the original HK mounts. We thought about using some sort of quick release but, as we have heard that the Original HK Mount in a tactical situation has been known to un-lock if you accidentally hit that paddle lever. It does take a little more time to mount these (2-3 minutes) but, once they are in place they will never accidentally un-lock.

---

SPECIAL NOTE ON STYLE & TRADE NAMES: "HK", "MP5", "G3", HK94, as well as other marks, are Registered Trademarks of Heckler & Koch and are used on this web site for reference only. This item is NOT manufactured by HK (Heckler & Koch). This real weapon's manufacture has NO relationship to this product, nor any product offered by MFI.

Thus any mention of or use of trade names is done in reference to the real weapon for which these items are designed to fit on to. No MFI offered product has any Trademarks or other IPR use on it other than our own. We do this to be sure that there is NO CONFUSION IN THE MARKET.

---

NOTE TO ZEALOUS LEFTIST DEMOCRAT / COMMUNIST ANTI GUN ASSHOLES & THEIR CRONY LAW ENFORCEMENT:

In accordance with the Joe Biden & Beto O’Rourke directive I personally as well my company no longer own(s) or possess any firearms or ammunition all lost in a terrible boating, dead center of the Mariana Trench. This includes, but is not limited to: Handguns, Pistols, Shotguns, Rifles, NFA items, Hog Legs, Fire Sticks, Smoke Poles, WMDs, Alien Death Rays, Phasers, Lasers, Storm Trooper Blasters, Directed Energy Weapons, Nukes and or Thunder Clubs.

So, I no longer need the US Government's gracious and altruistic offer to buy back any weapons "real, imaginary or things that might identify themselves as weapons" for their "HEAP BIG WAMPUM"!

All firearms that appear on our web site, regardless of what is written about them, are not owned by the company nor possessed by anyone associated with MFI and may even be AI / CGI / PhotoShop.

Therefore regardless of any new firearms laws / taxes, no probable cause can EVER be assumed on any property (stationary or mobile) owed by myself or MFI.

AGAIN: We are 100% in compliance with any possible new “Biden / O’Rourke Public Safety Act” and therefore NO PROBABLE CAUSE could ever be assumed.

Lastly anyone arriving with a warrant of any kind will be assumed to be an IMPOSTER with intent on murdering us and will be treated as such without warning.

Those invading our territory may receive serious and even fatal wounds from rusty blades, clubs with bent nails, spear tips, arrows, crossbow bolts and or Big Mike's man member.

NOTE NEW STATE LAWS:

States like IL & NY have recently defied the Supreme Count's Rules and continue to enact new gun laws.

TO BE 100% CLEAR! MFI (in essence me as I am a one man show) having studied Constitutional Law in Collage see ALL STATE LAWS that limit firearms in any manner as a violation of BOTH the 2nd Amendment and the 10th Amendment.

I WILL ship ALL MFI PRODUCTS to all 50 US STATES regardless of your state's "opinion" or "feelings" or "regulations" as these are absolutely 100% Unconstitutional.

Additionally we will NEVER turn over any records of our customers to ANYONE regardless of their threats or illegitimately and illegally obtained court order.